A CENTERED WICK MAKES A SAFER AND BETTER BURNING CANDLE... D507-667

                 

                     

                                      NEW AND IMPROVED WCT FOR CONTAINERS..

SMALL FITS: (INSIDE DIAMETER 2-3/4")

8oz Jelly Jars, 8oz Square Mason Jars, Flower Pot Votives and many more sizes..

NEW SIZE FITS: (INSIDE DIAMETER 2-7/8")

Different size containers in between the Small and Medium tools.

MEDIUM FITS: (INSIDE DIAMETER 3-1/16" TO 3-1/8")

16oz Elevation Jars, 13oz Tumblers, 8oz Tureens and many more sizes.                                  

LARGE FITS:

16oz Elevation Jars, 11oz Tureens and many more sizes.

Large has multiple holes and two wick clips for double wicking.

Wick Centering Tool Information

BELOW IS A LIST OF ADVANTAGES OF THE WCT FOR

CONTAINERS VERSUS OTHER WICK HOLDING DEVICES.

• THE TOOL IS MADE OF A HIGH HEAT RESISTANT PLASTIC.
• YOU CAN HEAT YOUR CONTAINERS WITH THE TOOL ON YOUR CONTAINER.
• YOU DON'T HAVE TO REMOVE THE TOOL UNTIL YOUR CANDLE CURES.
• THE NEW WICK CLIP ON EACH TOOL WILL HOLD THE WICK TAUT AND KEEP THE TOOL ON THE CONTAINER WITHOUT MOVING WICK OFF CENTER.
• I TESTED THE TOOL ON AN 8oz JELLY JAR CONTAINER WITH A 44 ZINC CORE WICK IN THE OVEN AT  220 DEGREES FOR 10 MINNUTES. NO PROBLEMS.
• I DID NOT TEST IN OVEN WITH ADAPTORS.. WOULD NOT ADVISE YOU TO DO THIS. IF YOU DO BE VERY CAREFULL...
• YOU CAN PRE WICK CONTAINERS AND PUT WCT ON TOP OF CONTAINER AND PLACE BACK IN BOX TO POUR AND LET CURE WITHOUT WORRYING ABOUT THE TOOL MOVING ON YOU.
• YOU CAN PLACE CONTAINERS CLOSE TOGETHER WHICH WILL GIVE YOU MORE SPACE ON YOUR POURING TABLE.
• YOU DON'T HAVE TO WORRY ABOUT BUMPING THE TOOL AND IT MOVING OFF CENTER ON YOU.
• THE WCT DOES NOT JUST HOLD THE WICK IT ALSO CENTERS IT AUTOMATICALLY. YOU DON'T HAVE TO BABYSIT THE TOOLS.
• TOOLS ARE FLEXIBLE, YOU CAN PRESS DOWN WHILE SETTING YOUR WICK AND THE TOOL WILL KEEP TENSION ON THE WICK AS IT CURES.
• YOU CAN BEND THE WICK OVER OR IF YOU USE A COTTON WICK OR JUST DON'T FEEL COMFORTABLE JUST BENDING THE WICK OVER YOU CAN USE A PAPER CLIP. THEY ARE CHEAP AND NOT BULKY LIKE USING CLOTHESPINS.
• THE TOOLS SIT ON TOP OF THE CONTAINERS AND WRAP AROUND THE SIDE. YOU ARE NOT LIMITED TO HOW HIGH YOU CAN POUR IN YOUR CONTAINERS.
• THE TOOL IS MADE OF PLASTIC SO YOU DON'T HAVE TO WORRY ABOUT IT BENDING OUT OF SHAPE OR RUSTING OR CORRODING FROM MOISTURE.
• IF YOU USE THE TOOLS AS DESIGNED THEY CAN LAST FOR YEARS.

THANKS TO ALL OUR CUSTOMERS THAT HAVE SENT US FEEDBACK...                  

(SPECIAL ORDERS)AVAILABLE IN MANY DIFFERENT SIZES ...

 Different ways to cover the wick hole in the bottom of the mold...

Concave or Molds with a base.

Flat bottom molds.

You don't have to use the Rod if you pour your candle with the wick already in the candle.

The Wick Centering Tool will hold the wick in the Center everytime.

WICK CENTERING TOOL FOR 3-WICK 5" & 6" ROUND

WICK CENTERING TOOL TM

TO ORDER GO TO OUR PRODUCT CATALOG....  

5" STRAIGHT FITS MOST SILICONE MOLDS BY JANET   $1.50 Ea.   PLUS S&H

FOR SILICONE MOLDS GO TO  http://www.creativegemsmolds.com/

VOTIVE WICK HOLE PUNCH....

THIS IS WHAT WE USE TO PUNCH THE WICK HOLE IN OUR VOTIVES.

WE POUR THE 3 OZ. REFILLS IN 3 OZ. DIXIE CUPS THEN WE TEAR THE

DIXIE CUP OFF OF THE CANDLE AND THEN PUNCH THE HOLE.

WE POUR THE 2 OZ. VOTIVES IN THE 2 OZ. MOLDS AND THEN

    PUNCH THE HOLES AFTER WE REMOVE THEM FROM THE MOLD. IF YOU PUT THEM 

IN THE FREEZER TO GET THEM OUT OF THE MOLDS LET THEM SET TO ROOM

              TEMPERATURE BEFORE PUNCHING HOLES OR IT WILL SPLIT THE CANDLE.   

WE USE A DRILL PRESS WITH A CHUCK IN IT AND A KNITTING

NEEDLE. SOUNDS CRAZY BUT IT WORKS JUST FINE. YOU CAN GET THE DRILL PRESS

AND ALL THE OTHER PARTS AT HOME DEPOT. YOU CAN EMAIL ME AND I WILL GIVE YOU A LIST

OF THE PARTS YOU NEED AND INSTRUCTIONS TO ASSEMBLE IT. IT REQUIRES A LITTLE BIT

OF MODIFICATIONS TO THE CHUCK NOTHING REAL HARD  JUST HAS TO BE DONE.

OR I WILL PURCHASE THE PARTS AND ASSEMBLE IT FOR YOU...

$79.99 PLUS S/H

CALL OR EMAIL FOR MORE INFORMATION